RUTX12

Specification:

Mobile

• Mobile module: 2 x 4G (LTE) - Cat 6 up to 300 Mbps, 3G - up to 42 Mbps
• Status: Signal Strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes Sent/Received, Bandwidth Combined, IMSI, ICCID, Carrier Aggregation
• SMS: SMS Status, SMS Setup, Send/Read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, Scheduled SMS, SMS Auto Reply, SMPP
• USSD: Supports sending and reading unstructured ancillary service data
• Blacklist/Whitelist: Blacklist/whitelist operators
• Multiple PDNs: Ability to use different PDNs for multiple network accesses and services
• Team management: Lock wristband, view status of wristband in use
• APN: Automatic APN
• Bridge: A direct connection (bridge) between a mobile ISP and a device on the LAN
• Go through: The router assigns its mobile WAN IP address to another device on the LAN

Wireless

• Wireless Mode: 802.11b/g/n/ac Wave 2 (WiFi 5) with data rates up to 867Mbps (Dual Band, MU-MIMO), 802.11r Fast Pass, Access Point (AP), Station (STA)
• Wi-Fi security: WPA2-Enterprise - PEAP, WPA2-PSK, WEP, WPA-EAP, WPA-PSK; AES-CCMP, TKIP, Auto Cipher modes, client separation
• SSID/ESSID: ESSID hidden mode
• Wi-Fi users: up to 150 simultaneous connections
• Wireless Access Point: Captive Portal (Hotspot), Internal/External Radius Server, SMS Authentication, Internal/External Landing Page, Walled Garden, User Scripts, URL Parameters, User Groups, Per User or Group Restrictions, User Management, 9 default customizable themes
• Wireless Features: Wireless Mesh (802.11s), Fast Roaming (802.11r), Relayd

Bluetooth

• Bluetooth 4.0: Bluetooth low energy (LE) for short range communication

Ethernet

• WAN: 1 x 10/100/1000Mbps WAN port, complies with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports MDI/MDIX auto crossover
• LAN: 4 x LAN ports, 10/100/1000 Mbps, complies with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports MDI/MDIX auto crossover

Web

• Routing: Static Routing, Dynamic Routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy Based Routing
• Network protocols: TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SMNP, MQTT, Wake On (WOL)
• VoIP pass-through support: H.323 and SIP-alg NAT helpers to properly route VoIP packets
• Connection monitoring: Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link control
• Firewall: Port forwarding, traffic rules, custom rules
• DHCP: Static and dynamic IP address allocation, DHCP relay
• QoS / Smart Queue Management (SQM): Traffic prioritization by source/destination, service, protocol or port, WMM, 802.11e
• DDNS: >25 service providers supported, the rest can be configured manually
• Network backup: Wi-Fi WAN, Mobile, VRRP, Wired options, all of which can be used as automatic failover
• Load balancing: Balance Internet traffic across multiple WAN connections
• SSHFS: Ability to mount a remote filesystem via SSH

Security

• Authentication: Shared Key, Digital Certificates, X.509 Certificates, TACACS+, Radius, IP and Login Attempt Blocking
• Firewall: Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; demilitarized zone; NATs; NAT-T
• Attack Prevention: DDOS Prevention (SYN Flood Protection, SSH Attack Prevention, HTTP/HTTPS Attack Prevention), Port Scan Prevention (SYN-FIN, SYN-RST, X-mas, NULL Flags, FIN Scan Attacks)
• VLAN: Port and tag based VLAN separation
• Mobile control: Mobile data limit, configurable period, start time, warning limit, phone number
• WEB Filter: Blacklist to block unwanted websites, Whitelist to only allow websites
• Access Control: Flexible TCP, UDP, ICMP packet access control, MAC address filter

VPN

• OpenVPN: Multiple clients and server can run simultaneously, 27 encryption methods
• OpenVPN encryption:DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128 , AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192 , AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256
• IPsec: IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES1 92GCM16 , AES256GCM16)
• GRE: GRE tunnel, GRE tunnel with IPsec support
• PPTP, L2TP: Client/server instances can run simultaneously, support L2TPv3, L2TP over IPsec
• Stunnel: Proxy server designed to add TLS encryption functionality to existing clients and servers without any code changes
• DMVPN: A method for building scalable IPsec VPNs
• SSTP: Support for SSTP client instances
• ZeroTier: ZeroTier VPN Customer Support
• WireGuard: Support for WireGuard VPN client and server
• Tinc: Tinc offers encryption, authentication and compression in its tunnels. Client and server support

Modbus TCP Slave

• ID range: Reply to one ID in the range [1;255] or any
• Allow Permission: Permit access over WAN
• Custom registers: MODBUS TCP custom register block requests that read/write a file inside the router and can be used to extend MODBUS TCP Slave functionality

Modbus TCP Master

• Supported functions: 01, 02, 03, 04, 05, 06, 15, 16
• Supported data format: 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)

Server Details

• Protocol: HTTP(S), MQTT, Azure MQTT, Kinesis

MQTT gateway

• MQTT Gateway: Allows sending commands and receiving data from MODBUS Master via MQTT Broker

DNP3

• Supported modes: TCP master station, DNP3 outdoor station

Monitoring and Management

• WEB Interface: HTTP/HTTPS, Status, Configuration, Firmware Upgrade, CLI, Troubleshooting, Event Log, System Log, Kernel Log
• FOTA: Firmware update from server, automatic notification
• SSH: SSH (v1, v2)
• SMS: SMS status, SMS configuration, sending/reading SMS via HTTP POST/GET
• Call: Reboot, status, mobile data on/off, call out/out, timer answer/hang up, Wi-Fi on/off
• TR-069: OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
• MQTT: MQTT Broker, MQTT Issuer
• SNMP: SNMP (v1, v2, v3), SNMP trap
• JSON-RPC: HTTP/HTTPS Management API
• MODBUS: MODBUS TCP state/control
• RMS: Teltonika Remote Management System (RMS)

IOT Platforms

• Cloud of Things: Allows you to monitor: device data, mobile data, network information, accessibility
• ThingWorx: Allows you to monitor: WAN type, WAN IP address, mobile carrier name, mobile signal strength, mobile network type
• Cumulocity: Allows you to monitor: device model, version and serial number, WAN type and IP address, mobile cell ID, ICCID, IMEI, connection type, carrier, signal strength
• Azure IoT Hub: Can send device IP address, number of bytes sent/received, temperature, number of PINs to Azure IoT Hub server, mobile connection status, network link status, IMEI, ICCID, model, manufacturer, serial number, version, IMSI, SIM status, PIN status, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type

System characteristics

• Processor: ARM Cortex A7 quad-core, 717MHzc
• RAM: 256MB, DDR3
• FLASH Memory: 256MB, SPI Flash Memory

Firmware/Config

• WEB interface: FW update from file, check FW on server, configuration profiles, configuration backup
• FOTA: Firmware update
• RMS: Firmware update/configuration for multiple devices at once
• Save settings: FW update without losing current configuration

Firmware customization

• Operating system: RutOS (OpenWrt-based Linux operating system)
• Supported languages: Busybox Shell, Lua, C, C++ and Python, Java in Package Manager
• Development tools: SDK with build environment provided

Location tracking

• GNSS: GPS, GLONASS, BeiDou, Galileo and QZSS
• Coordinates: GNSS coordinates via WebUI, SMS, TAVL, RMS
• NMEA: NMEA0183
• NTRIP: NTRIP (Internet Protocol RTCM Network Transport)
• Server software: TAVL, RMS server software supported
• Geofencing: Configurable multiple geofences

USB

• Data transmission speed: USB 2.0
• Applications: Samba Share, USB to Serial Connection
• External devices: Ability to connect an external hard drive, flash drive, additional modem, printer, USB-to-serial adapter
• Storage formats: FAT, FAT32, exFAT, NTFS (read only), ext2, ext3, ext4

Input/Output

• Input: 1 x digital input, 0-6V sensed logic low, 8-30V sensed logic high
• Output: 1 x digital output, open collector output, max. output 30V, 300mA
• Events: Email, RMS, SMS
• I/O juggler: Allows you to set specific I/O conditions to trigger an event

Power

• Connector: 4-pin industrial DC power socket
• Input voltage range: 9-50 VDC, reverse polarity protection, surge/transient protection
• PoE (passive): Can be powered via LAN1 port, not compliant with IEEE802.3af, 802.3at and 802.3bt, Mode B, 9 - 30 VDC
• Power Consumption: Idle: <4W, Max: <22W

Physical interfaces

• Ethernet: 5 RJ45 ports, 10/100/1000Mbps
• I/O: 1 x digital input, 1 x digital output on 4-pin power connector
• LEDs: 4 x Link Status LEDs, 6 x Link Strength LEDs, 10 x Ethernet Port Status LEDs, 4 x WAN Status LEDs, 1 x Power LED, 2 x 2.4G Wi-Fi and 5G
• SIM: 2 x SIM slots (Mini SIM - 2FF), 1.8V/3V, external SIM holders
• Power: 1 x 4-pin power connector
• Antennas: 4 x SMA for LTE, 2 x RP-SMA for WiFi, 1 x RP-SMA for Bluetooth, 1 x SMA for GNNS
• USB: 1 x USB A port for external devices
• Reset: Reboot/Reset User Defaults/Factory Reset Button
• Others: 1 x ground screw

Physical Specification

• Enclosure type: Aluminum housing
• Dimensions (W x H x D): 132 x 44.2 x 95.1mm
• Weight: 540 gr
• Mounting options: DIN rail (can be mounted on both sides), placing on a flat surface

Operating environment

• RUTX12 operating temperature: -40°C to 75°C
• Operating humidity: 10% to 90% non-condensing
• Ingress protection: IP30

Warranty: 2 years

---