Industrial Ethernet router, 4 Gigabit LAN ports, WiFi - RUTX10

Specification:

Ethernet

• WAN: 1 x 10/100/1000Mbps WAN port, complies with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports MDI/MDIX auto crossover
• LAN: 3 x LAN ports, 10/100/1000 Mbps, complies with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports MDI/MDIX auto crossover

Wireless

• Wireless Mode: 802.11b/g/n/ac Wave 2 (WiFi 5) with data rates up to 867Mbps (Dual Band, MU-MIMO), 802.11r Fast Pass, Access Point (AP), Station (STA)
• Wi-Fi security: WPA2-Enterprise - PEAP, WPA2-PSK, WEP, WPA-EAP, WPA-PSK; AES-CCMP, TKIP, Auto Cipher modes, client separation
• SSID/ESSID: ESSID hidden mode
• Wi-Fi users: up to 150 simultaneous connections
• Wireless access point: Captive portal (Hotspot), internal/external Radius server, SMS authorization, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customizable themes
• Wireless features: Wireless mesh (802.11s), fast roaming (802.11r), Relayd

Bluetooth

• Bluetooth 4.0: Bluetooth low energy (LE) for short range communication

Web

• Routing: Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routing
• Network protocols: TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SMNP, MQTT, Wake On Lan (WOL)
• VoIP transit support: H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
• Connection monitoring: Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link control
• Firewall: Port forwarding, traffic rules, custom rules
• DHCP: Static and dynamic IP address allocation, DHCP Relay
• QoS / Smart Queue Management (SQM): Traffic prioritization by source/destination, service, protocol or port, WMM, 802.11e
• DDNS: >25 service providers supported, the rest can be configured manually
• Network backup: Wi-Fi WAN, VRRP, wired options, all of which can be used as automatic failover
• Load balancing: Balance Internet traffic across multiple WAN connections
• SSHFS: Ability to mount a remote filesystem via SSH

Security

• Authentication: Shared Key, Digital Certificates, X.509 Certificates, TACACS+, Radius, IP and Login Attempt Blocking
• Firewall: Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; demilitarized zone; NATs; NAT-T
• Attack Prevention: DDOS Prevention (SYN Flood Protection, SSH Attack Prevention, HTTP/HTTPS Attack Prevention), Port Scan Prevention (SYN-FIN, SYN-RST, X-mas, NULL Flags, FIN Scan Attacks)
• VLAN: Port and tag based VLAN separation
• Mobile control: Mobile data limit, configurable period, start time, warning limit, phone number
• WEB Filter: Blacklist to block unwanted websites, Whitelist to only allow websites
• Access Control: Flexible TCP, UDP, ICMP packet access control, MAC address filter

VPN

• OpenVPN: Multiple clients and server can run simultaneously, 27 encryption methods
• OpenVPN encryption: DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192, BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128 , AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192 , AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256
• IPsec: IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES1 92GCM16 , AES256GCM16)
• GRE: GRE tunnel, GRE tunnel with IPsec support
• PPTP, L2TP: Client/server instances can run simultaneously, support L2TPv3, L2TP over IPsec
• Stunnel: Proxy server designed to add TLS encryption functionality to existing clients and servers without any code changes
• DMVPN: A method for building scalable IPsec VPNs
• SSTP: Support for SSTP client instances
• ZeroTier: ZeroTier VPN Customer Support
• WireGuard: Support for WireGuard VPN client and server
• Tinc: Tinc offers encryption, authentication and compression in its tunnels. Client and server support.

Modbus TCP Slave

• ID range: Reply to one ID in the range [1;255] or any
• Allow Permission: Permit access over WAN
• Custom registers: MODBUS TCP custom register block requests that read/write a file inside the router and can be used to extend MODBUS TCP Slave functionality

Modbus TCP Master

• Supported functions: 01, 02, 03, 04, 05, 06, 15, 16
• Supported data format: 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)

Server Details

• Protocol: HTTP(S), MQTT, Azure MQTT, Kinesis

MQTT gateway

• MQTT Gateway: Allows sending commands and receiving data from MODBUS Master via MQTT Broker

DNP3

• Supported modes: TCP master station, DNP3 outdoor station

Monitoring and Management

• WEB Interface: HTTP/HTTPS, Status, Configuration, Firmware Upgrade, CLI, Troubleshooting, Event Log, System Log, Kernel Log
• FOTA: Firmware update from server, automatic notification
• SSH: SSH (v1, v2)
• TR-069: OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
• MQTT: MQTT Broker, MQTT Issuer
• SNMP: SNMP (v1, v2, v3), SNMP trap
• JSON-RPC: HTTP/HTTPS Management API
• MODBUS: MODBUS TCP state/control
• RMS: Teltonika Remote Management System (RMS)

IOT Platforms

• Cloud of Things: Allows you to monitor: device data, mobile data, network information, accessibility
• ThingWorx: Allows you to monitor: WAN type, WAN IP address, mobile carrier name, mobile signal strength, mobile network type
• Cumulocity: Allows you to monitor: device model, version and serial number, WAN type and IP address, mobile cell ID, ICCID, IMEI, connection type, operator, signal strength
• Azure IoT Hub: Can send device IP address, bytes sent/received, temperature and PIN number to Azure IoT Hub server

System characteristics

• Processor: ARM Cortex A7 quad-core, 717MHzc
• RAM: 256MB, DDR3
• FLASH Memory: 256MB, SPI Flash Memory

Firmware/Config

• WEB interface: FW update from file, check FW on server, configuration profiles, configuration backup
• FOTA: Firmware update
• RMS: Firmware update/configuration for multiple devices at once
• Save settings: FW update without losing current configuration

Firmware customization

• Operating system: RutOS (OpenWrt-based Linux operating system)
• Supported languages: Busybox Shell, Lua, C, C++ and Python, Java in Package Manager
• Development tools: SDK with build environment provided

USB

• Data transmission speed: USB 2.0
• Applications: Samba Share, USB to Serial Connection
• External devices: Ability to connect an external hard drive, flash drive, additional modem, printer, USB-to-serial adapter
• Storage formats: FAT, FAT32, exFAT, NTFS (read only), ext2, ext3, ext4

Input/Output

• Input: 1 x digital input, 0-6V sensed logic low, 8-30V sensed logic high
• Output: 1 x digital output, open collector output, max. output 30V, 300mA
• Events: Email, RMS
• I/O juggler: Allows you to set specific I/O conditions to trigger an event

Power

• Connector: 4-pin industrial DC power socket
• Input voltage range: 9-50 VDC, reverse polarity protection, surge/transient protection
• PoE (passive): Can be powered via LAN1 port, not compliant with IEEE802.3af, 802.3at and 802.3bt, Mode B, 9 - 30 VDC
• Power consumption: 9W max

Physical interfaces

• Ethernet: 4 RJ45 ports, 10/100/1000Mbps
• I/O: 1 x digital input, 1 x digital output on 4-pin power connector
• LEDs: 8 LAN status LEDs, 1 power LED, 2.4G & 5G Wi-Fi 2 LEDs
• Power: 1 x 4-pin power connector
• Antennas: 2 x RP-SMA for Wi-Fi, 1 x RP-SMA for Bluetooth
• USB: 1 x USB A port for external devices
• Reset: Reboot/Reset User Defaults/Factory Reset Button
• Others: 1 x ground screw

Physical Specification

• Enclosure type: Aluminum housing
• Dimensions (W x H x D): 115 x 32.2 x 95.2mm
• Weight: 355 gr
• Mounting options: DIN rail, flat surface placement

Operating environment

• RUTX10 operating temperature: -40°C to 75°C
• Operating humidity: 10% to 90% non-condensing
• Ingress protection: IP30

Warranty: 2 years

---